Search code examples
linuxsshserverclientyocto

I can not connect to ssh server

I would be very glad for some advice. Hello guys I have Linux development board, which runs ssh-server-dropbear. Then the board is connected via ethernet cord into our local network(into router). Command "ip a" works. I installed open-ssh on my ubuntu 16.04. I'm using VMware simulator on windows 10 computer. When I try to ssh into the board from ubuntu with command: ssh [email protected] the command is running, but I can not connect. The output is:

"ssh: connect to host 192.168.30.202 port 22: Connection refused"

Can someone know why it could be a problem? I tried this on 2 computers. One was laptop and second is full pc. I was thinking that it could be, because the VMware workstation, but I tried all types of network setting and it's still same.

I is development board http://www.myirtech.com/list.asp?id=573 . I have windows 10 and on in VMWorkstation with Ubuntu.

SSH SERVER

root@myd-y6ull14x14:~# ssh
Dropbear SSH client v2019.78 https://matt.ucc.asn.au/dropbear/dropbear.html
Usage: ssh [options] [user@]host[/port][,[user@]host/port],...] [command]
-p <remoteport>
-l <username>
-t    Allocate a pty
-T    Don't allocate a pty
-N    Don't run a remote command
-f    Run in background after auth
-y    Always accept remote host key if unknown
-y -y Don't perform any remote host key checking (caution)
-s    Request a subsystem (use by external sftp)
-o option     Set option in OpenSSH-like format ('-o help' to list options)
-i <identityfile>   (multiple allowed, default .ssh/id_dropbear)
-A    Enable agent auth forwarding
-L <[listenaddress:]listenport:remotehost:remoteport> Local port forwarding
-g    Allow remote hosts to connect to forwarded ports
-R <[listenaddress:]listenport:remotehost:remoteport> Remote port forwarding
-W <receive_window_buffer> (default 24576, larger may be faster, max 1MB)
-K <keepalive>  (0 is never, default 0)
-I <idle_timeout>  (0 is never, default 0)
-B <endhost:endport> Netcat-alike forwarding
-J <proxy_program> Use program pipe rather than TCP connection
-c <cipher list> Specify preferred ciphers ('-c help' to list options)
-m <MAC list> Specify preferred MACs for packet verification (or '-m help')
-b    [bind_address][:bind_port]
-V    Version

ip a

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN group default qlen 10
    link/can 
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 0a:df:74:e2:6f:39 brd ff:ff:ff:ff:ff:ff
    inet 192.168.30.202/24 brd 192.168.30.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::8df:74ff:fee2:6f39/64 scope link 
       valid_lft forever preferred_lft forever
4: eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN group default qlen 1000
    link/ether ee:e1:a2:03:a9:fb brd ff:ff:ff:ff:ff:ff
5: sit0@NONE: <NOARP> mtu 1480 qdisc noop state DOWN group default qlen 1000
    link/sit 0.0.0.0 brd 0.0.0.0
Solution

  • The problem was in my windows DNS setting, in past I set the DNS to manuall, after I switch the setting back to automatic the ssh connection works, how it should.