Within the intel intrinsics guide some operations are defined using a term "MAX". An example is __m256 _mm256_mask_permutexvar_ps (__m256 src, __mmask8 k, __m256i idx, __m256 a), which is defined as
FOR j := 0 to 7
i := j*32
id := idx[i+2:i]*32
IF k[j]
dst[i+31:i] := a[id+31:id]
ELSE
dst[i+31:i] := 0
FI
ENDFOR
dst[MAX:256] := 0
. Please take note of the last line within this definition: dst[MAX:256] := 0. What is MAX referring to and is this line even adding any valuable information? If I had to make assumptions, then MAX probably means the amount of bits within the vector, which is 256 in case of _mm256. This however does not seem to change anything for the definition of the operation and might as well have been omitted. But why is it there then?
This pseudo-code only makes sense for assembly documentation, where it was copied from, not for intrinsics. (HTML scrape of Intel's vol.2 PDF documenting the corresponding vpermps asm instruction.)
...
ENDFOR
DEST[MAXVL-1:VL] ← 0
(The same asm doc entry covers VL = 128, 256, and 512-bit versions, the vector width of the instruction.)
In asm, a YMM register is the low half of a ZMM register, and writing a YMM zeroes the upper bits out to the CPU's max supported vector width (just like writing EAX zero-extends into RAX).
The intrinsic you picked is for the masked version, so it requires AVX-512 (EVEX encoding), thus VLMAX is at least 5121. If the mask is a constant all-ones, it could get optimized to the AVX2 VEX encoding, but both still zero high bits of the full register out to VLMAX.
The intrinsics API just has __m256 and __m512 types; an __m256 is not implicitly the low half of an __m512. You can use _mm512_castps256_ps512 to get a __m512 with your __m256 as the low half, but the API documentation says "the upper 256 bits of the result are undefined". So if you use it on a function arg, it doesn't force it to vmovaps ymm7, ymm0 or something to zero-extend into a ZMM register in case the caller left high garbage.
If you use _mm512_castps256_ps512 on a __m256 that came from an intrinsic in this function, it pretty much always will happen to compile with a zeroed high half whether it stayed in a reg or got stored/reloaded, but that's not guaranteed by the API. (If the compiler chose to combine a previous calculation with something else, using a 512-bit operation, you could plausibly end up with a non-zero high half.) If you want high zeros, there's no equivalent to _mm256_set_m128 (__m128 hi, __m128 lo), so you need some other explicit way.
Footnote 1: Or with some hypothetical future extension, VLMAX aka MAXVL could be even wider. It's determined by the current value of XCR0. This documentation is telling you these instructions will still zero out to whatever that is.
(I haven't looked into whether changing VLMAX is possible on a machine supporting AVX-512, or if it's read-only. IDK how the CPU would handle it if you can change it, like maybe not running 512-bit instructions at all. Mainstream OSes certainly don't do this even if it's possible with privileged operations.)
SSE didn't have any defined mechanism for extension to wider vectors, and some existing code (notably Windows kernel drivers) manually saved/restored a few XMM registers for their own use. To support that, AVX decided that legacy SSE would leave the high part of YMM/ZMM registers unmodified. But to run existing machine code using non-VEX legacy SSE encodings efficiently, it needed expensive state transitions (Haswell and Ice Lake) and/or false dependencies (Skylake): Why is this SSE code 6 times slower without VZEROUPPER on Skylake?
Intel wasn't going to make this mistake again, so they defined AVX as zeroing out to whatever vector width the CPU supports, and document it clearly in every AVX and AVX-512 instruction encoding. Thus VEX and EVEX can be mixed freely, even being useful to save machine-code size: