How do I tell libpcap v1.6.2 to store nanosecond values in struct pcap_pkthdr::ts.tv_usec (instead of microsecond values) when capturing live packets?
(Note: This question is similar to How to enable nanosecond resolution when capturing live packets in libpcap? but that question is vague enough that I decided to ask a new question.)
For offline and "dead" captures, the following functions can be used to tell libpcap to fill the struct pcap_pkthdr's ts.tv_usec member with nanosecond values:
pcap_open_dead_with_tstamp_precision()pcap_open_offline_with_tstamp_precision()pcap_fopen_offline_with_tstamp_precision()Unfortunately, there does not appear to be _with_tstamp_precision variants for pcap_open_live() or pcap_create().
I believe that capturing live packets with nanosecond resolution should be possible, because the changelog for v1.5.0 says (emphasis mine):
Add support for getting nanosecond-resolution time stamps when capturing and reading capture files
I did see the pcap_set_tstamp_type() function and the pcap-tstamp man page, which says:
PCAP_TSTAMP_HOST—host: Time stamp provided by the host on which the capture is being done. The precision of this time stamp is unspecified; it might or might not be synchronized with the host operating system's clock.PCAP_TSTAMP_HOST_LOWPREC—host_lowprec: Time stamp provided by the host on which the capture is being done. This is a low-precision time stamp, synchronized with the host operating system's clock.PCAP_TSTAMP_HOST_HIPREC—host_hiprec: Time stamp provided by the host on which the capture is being done. This is a high-precision time stamp; it might or might not be synchronized with the host operating system's clock. It might be more expensive to fetch thanPCAP_TSTAMP_HOST_LOWPREC.PCAP_TSTAMP_ADAPTER—adapter: Time stamp provided by the network adapter on which the capture is being done. This is a high-precision time stamp, synchronized with the host operating system's clock.PCAP_TSTAMP_ADAPTER_UNSYNCED—adapter_unsynced: Time stamp provided by the network adapter on which the capture is being done. This is a high-precision time stamp; it is not synchronized with the host operating system's clock.
Does the phrase "high-precision time stamp" here mean that nanosecond values are stored in the header's ts.tv_usec field? If so, PCAP_TSTAMP_HOST says "unspecified", so how do I determine at runtime whether the ts.tv_usec field holds microseconds or nanoseconds? And which of these is the default if pcap_set_tstamp_type() is never called?
pcap_create() does little if anything to set parameters for the capture device, and has no alternative calls for setting those parameters; this is by design. The intent, at the time pcap_create() and pcap_activate() were introduced, was that neither of those calls would have to be changed in order to support new parameters, and that new APIs would be introduced as new parameters are introduced.
You're supposed to call pcap_create() to create a not-yet-activated handle, set the parameters with the appropriate calls, and then attempt to activate the handle with pcap_activate().
One of the appropriate calls is pcap_set_tstamp_precision(), which is the call you use between pcap_create() and pcap_activate() to specify that you want nanosecond-precision time stamps. The default is microsecond-precision time stamps, for backwards source and binary compatibility.
Note that pcap_set_tstamp_precision() will fail if you can't get nanosecond-precision time stamps from the device on which you're capturing, so you must check whether it succeeds or fails or call pcap_get_tstamp_precision() after activating the pcap_t in order to see what time stamp precision you'll be getting.
And, no, "high-precision" has nothing to do with whether you get microseconds or nanoseconds, it has to do with whether the nominal microseconds or nanoseconds value really provide microsecond or nanosecond granularity or whether you'll always get values that are multiples of a power of 10 because the clock being used doesn't measure down to the microsecond or nanosecond.